Easy Lug nut removal

Post here for Steering ,suspension and tires discussion
Author
Message
Offline
Moderator
Moderator
Posts: 1199
Joined: Sat Jan 26, 2013 2:32 am
Travco Model:
Location: Kerrville, Texas

Re: Easy Lug nut removal

Unread post by 77Travco » Thu May 19, 2016 2:11 pm

When you buy the stud, post up a part number. Hopefully it's not a big deal to find one.

Zed
Offline
Contributing Member
Contributing Member
Posts: 85
Joined: Fri Aug 12, 2016 12:58 am
Travco Model: 270 Mahal

Re: Easy Lug nut removal

Unread post by Zed » Mon Nov 21, 2016 1:12 am

Can OP post up the math formula he used to figure out the amount of torque needed in foot inches to get a specific torque in foot pounds out of this unit? I just bought one and I have completely taken all the drums off to inspect and clean the brakes and I need to re torque everything. \n\nI think this unit is a 1:78 ratio drive so to achieve 450 foot lbs I would divide 450 by 78 which gives me 5.7 (rounded up) which converted to foot inches would be 5.7 x 12 which gives me 68.4 foot inches to achieve 450 foot pounds on the other end. Is this math correct?\n\nThanks.

Offline
Site Admin
Site Admin
Posts: 1233
Joined: Wed Nov 19, 2014 2:26 pm
Travco Model: 76 Mahal 2+2
Location: Arnoldsville GA
Contact:

Re: Easy Lug nut removal

Unread post by KB2CRK » Mon Nov 21, 2016 6:34 am

I don't remember the formula right now. I think I divided 500 by the reduction and came out with a very low ftlbs number. I then used an online converter to get the inch lbs. I believe for 500 ft lbs it was 76 in lbs so I think your conversion is close if not right.

Offline
Site Admin
Site Admin
Posts: 1782
Joined: Tue Jan 22, 2013 7:01 am
Travco Model: 1975 270,1974 220
Location: North East Ct

Re: Easy Lug nut removal

Unread post by Acesneights » Wed Nov 23, 2016 8:39 pm

Too bad our Travcos are not 24v. I have one of these for my 5 ton. it works awesome. \n\nhttp://www.ebay.com/itm/Roboimpact-Robo-Electr ... 75&vxp=mtr
1977 Travco 270 Elite\n1974 Travco 220 Parts unit

Offline
Senior Contributor
Senior Contributor
Posts: 629
Joined: Fri Feb 21, 2014 10:32 am
Travco Model: 270
Location: Ohio

Re: Easy Lug nut removal

Unread post by badbillybiker » Wed Nov 23, 2016 9:27 pm

CURIOUS... I acquired a 24 volt wheel chair charger under forgetable circumstances ages ago and never used it...... Wouldnt one runnning from the travco genset power the 24v charger to operate a 24v piece of equipment?... \nmaybe thru a 2 - 12volt battery bank? btw, i am a electrically challenged person...2btw, i too got one of those multipliers but never took it out of the box/carton...\nBBB

Offline
Site Admin
Site Admin
Posts: 1233
Joined: Wed Nov 19, 2014 2:26 pm
Travco Model: 76 Mahal 2+2
Location: Arnoldsville GA
Contact:

Re: Easy Lug nut removal

Unread post by KB2CRK » Thu Nov 24, 2016 9:07 am

badbillybiker wrote:CURIOUS... I acquired a 24 volt wheel chair charger under forgetable circumstances ages ago and never used it...... Wouldnt one runnning from the travco genset power the 24v charger to operate a 24v piece of equipment?... \nmaybe thru a 2 - 12volt battery bank? btw, i am a electrically challenged person...2btw, i too got one of those multipliers but never took it out of the box/carton...\nBBB
\nI have at least had it out of its box. Tried it even. One hand on the crank and I can spin the lugs off. This was after tightening them with a 4' breaker bar with all 260 lbs of my weight on it.

Offline
Senior Contributor
Senior Contributor
Posts: 629
Joined: Fri Feb 21, 2014 10:32 am
Travco Model: 270
Location: Ohio

Re: Easy Lug nut removal

Unread post by badbillybiker » Thu Nov 24, 2016 9:56 am

As I am constantly on the hunt for Travco part numbers.. \nhas anyone seen the part number for that stud posted yet?

Offline
Senior Contributor
Senior Contributor
Posts: 629
Joined: Fri Feb 21, 2014 10:32 am
Travco Model: 270
Location: Ohio

Re: Easy Lug nut removal

Unread post by badbillybiker » Thu Nov 24, 2016 10:05 am

As I am constantly on the hunt for more Travco part numbers.. \nHas anyone seen the part number for that stud posted about yet?\nBe nice to have a spare or two to put into my "new" parts bin...\nPresuming it should be a low cost item, I'll take two...\nBBB

Post Reply

Return to “Steering,Suspension and Tires”